304 Stainless Steel Sintered Felt Polyester Melt Filter

304 Stainless Steel Sintered Felt Polyester Melt Filter

  • Model NO.: Customer design
  • Sizes: Customer Design
  • Trademark: TIANRUI
  • Origin: Xinxiang Henan China
  • Filter Media: Stainless Steel Sintered Felt
  • Application: Filtering Polyester
  • Specification: ISO
  • HS Code: 8421999000

Polyester Melt Filter Element

1. DESCRIPTION

Apply to polymer filtration with high temperature, high pressure and high viscosity to filter solid particle and slimes in medium and effectively control cleanliness.

Made from 100% stainless steel,can be cleaned and used repeatedly.The filter element which made of import stainless steel fiber felt,with good permeability, the larger pollutant capacity and long use life.The filter element which made of stainless steel wire mesh,with uniform pore size, high strength, good process ability and easy to clean.Bellows-type filters used in chemical fiber, textile system,  etc.

2. TECHNICAL DATA

Operating pressure:≤ 31.7MPa      Operating temperature:≤300ºC

Medium viscosity:≤260Pa.S            Permissible pressure:≤10MPa

Absolute precision

(μ)

Bubbling pressure 
  (Pa)

The average porosity
  (L/dm2/min)

Thickness
  (mm)

Weight 
  (g/m2)

Poriness
  (%)

Pollutant holding quantity
  (mg/cm2)

3

12300

9

0.35

975

65

6.40

5

7600

34

0.34

600

78

5.47

7

5045

57

0.27

600

72

6.47

10

3700

100

0.32

600

77

7.56

15

2470

175

0.37

600

80

7.92

20

1850

255

0.49

750

81

12.44

25

1480

320

0.61

1050

79

19.38

30

1235

455

0.63

1050

79

23.07

40

925

580

0.66

1200

77

25.96

60

630

1000

0.70

750

87

33.97

Note:

1. The above data refer to Bekaert AL3 series filter felt;

2. The bubbling pressure test up to ISO4003 standards;

3. The average porosity experiment up to ISO4022 standards, air pressure is 200 pa;

4. The pollutant holding quantity experiment up to ISO4572 standard. The felt's final pressure drop is 8 times for the initial pressure drop.
304 Stainless Steel Sintered Felt Polyester Melt Filter

1.MODEL

L(mm)

D(mm)

M

filter area

R(μm )

Filter material

PF-86/200-R

200

86

M65x2P

0.20m²

3, 5, 7, 10, 15, 20, 25, 30, 40, 60, 75

Stainless steel fiber felt, stainless steel woven   mesh

PF-86/350-R

350

0.35m²

PF-86/500-R

500

0.50m²

PF-100/800-R

800

100

M80x2P

1.00m²

2.MODEL

L(mm)

D(mm)

M

filter area

R(μm )

Filter material

PF-65/250-R

250

65

226
  223
  220
  215

0.135m²

 

 

3, 5, 7, 10, 15, 20, 25, 30, 40, 60, 75

 

Stainless steel fiber felt,   stainless steel woven mesh

PF-65/500-R

500

0.38m²

PF-70/750-R

750

70

0.42m²

PF-70/750-R

750

70

0.60m²

3.MODEL

L(mm)

D(mm)

M

filter area

R(μm )

Filter material

PF-35/102-R

102

35

M18
  M20x2.5
  M20x1.5
  NPT1"
  3/4-16

0.026 m²

 

3, 5, 7, 10, 15, 20, 25, 30, 40, 60, 75

Stainless steel fiber felt,   stainless steel woven mesh

PF-35/207-R

207

0.07 m²

PF-35/210-R

210

0.07 m²

PF-35/242-R

242

0.08 m²

PF-35/425-R

425

0.15 m²

PF-35/485-R

485

0.20 m²

4.MODEL

L(mm)

D(mm)

M

filter area

R(μm )

Filter material

PF-60/1432-R

1432

60

2"x12UN-2A

1.015m²

3, 5, 7, 10, 15, 20, 25, 30, 40, 60, 75

Stainless steel fiber felt, stainless steel woven   mesh

PF-60/1241-R

1241

0.98m²

PF-60/1025-R

1025

0.81m²

304 Stainless Steel Sintered Felt Polyester Melt Filter
304 Stainless Steel Sintered Felt Polyester Melt Filter

Cross Roller Bearing is a special type bearing. Because of the inner ring or outer ring were separated, after loading the roller and the cage, it is fixed with the cross roller shaft ring to prevent the separation, so the operation is simple when installing the cross roller shaft ring. Since the rollers are intersected, only one set of cross roller bearings can withstand the load in each direction, which is three to four times more rigid than the traditional model. At the same time, because the inner ring or outer ring of the cross Roller Bearing is a two-part structure, the bearing clearance can be adjusted, and even if it is preloaded, it can obtain a high-precision rotary motion. Moreover, because of its special structure, it is commonly used in industrial robots as joint bearings.

cross roller 1

The classification and model series of cross roller bearings are below:

RB type (outer ring segment)

RB series models for cross roller bearing, basic, inner and outer ring size is minimal to miniaturization, its structure is the outer ring is divided, the inner ring design is an organic whole, the inner ring spinning of high precision parts suitable for requirements.

RE type (inner ring segment)

The RE series is a new type of XRB design concept, which is the same size as the XRB type.The structure of the inner ring is the split type and the outer ring is one design, which is suitable for the parts with high rotating precision of outer ring.

RU type (inner and outer circle)

The RU series model is not required to be fixed flange and support base due to the processing of mounting holes.In addition, due to the adoption of the integrated inner and outer ring structure of the belt, the installation has little effect on the performance, thus achieving stable rotation precision and torque.Can be used for outer ring and inner ring rotation.

RBC type (outer ring segment)

The RBC series model (corresponding to the CRBC series of IKO company) is composed of the outer ring is the split type, the inner ring is one design, and the belt is fully loaded with roller bearings.Suitable for high rotation accuracy of inner ring.

CRBH type (inner and outer ring)

CRBH series model, outer ring and outer ring are integral structure, used for outer ring and inner ring rotation.

RA type (outer circle segmentation, ultrathin type)

The RA series model is the compact type that reduces the thickness of RB and outer ring to the limit.Suitable for areas with light weight and compact design, such as rotating parts of robot and manipulator.

SX type (outer ring segment)

The structure of SX series is similar to that of RB series. The outer ring is a two-part structure, which is designed with three spring card rings and the inner ring, which is suitable for the place where the inner ring has high rotation precision.

XRU08 type (inside and outside)

XSU08 series is similar to the RU series, and the inner and outer rings have been machined with holes, so no fixed flange and support seats are required.Due to the adoption of the integrated inner and outer ring structure, the installation has little effect on the performance, thus achieving stable rotation precision and torque.Can be used for outer ring and inner ring rotation.


We believe that we can supply the best service and price for your, hope to make a long-term cooperation with you. If you have any question please do not hesitate contact with us. We keep warmly welcome you visit us in any time.


Cross Roller Bearing

Cross Roller Bearing,Excavator Parts Cross Roller Bearings,High Precision Cross Roller Bearing,Thin Section Cross Roller Slewing Bearing

LUOYANG AUTO BEARING CO.,LTD , http://www.lyautobearing.com